Pump & Meter Service, Inc.

Owner:

Penske Truck

Scope Of Work

Removals and Tank Restoration

Fuel System Installation Equipment
Qty    Description    
1    Wall Hydrant
12    Bollard Covers/Sleeves
1    JE Adams Vacuum
4    Riverside S/S Island Forms 4’x6’x13”
7    4” Clean Outs
12    8” Bollards
2    6’x7’ Steel Post for lube racks
4    Collection boxes
    Canopy Downspouts

Fuel System Installation
Description    
•    Prep excavation for (1) 20,000-gallon UST, (1) 4,000-gallon UST, and (1) 2,000-gallon UST.
•    Air test tanks, set precast deadmen, set tanks, install anchor straps and secure. 
•    Backfill with pea rock, trench from tanks to Fuel Island. Set tank sumps. 
•    Pipe (3) 2” FRP vent lines from tanks. Vents above grade to be 2” steel pipe; pipe (3) new fill assemblies (Diesel, Gas and DEF). Apply corrosion protection to all underground metal components. 
•    Run 4” corrugated chase pipe. Pull 2” DW Fiberglass from tanks to dispenser sumps.
•    Pipe 2” LCX to each DEF dispenser creating a closed loop for recirculation.  ***In Minnesota you cannot pipe DEF without either heating the line or putting in a recirculation system.  We have figured recirculation and this requires the TLS450+ to have the necessary components to do so.
•    Pipe 2” LCX to (1) single sided diesel dispenser, (1) master/satellite diesel dispenser, and (1) single sided diesel satellite dispenser.
•    Per drawing F6.0 detail G. Pipe and plumb DEF fill station. Route piping thru 6” PVC piping chase. At exit point in concrete use spray foam and self-leveling caulk.
•    Pipe 2” LCX to (1) dual sided gasoline dispenser. 
•    Pipe (3) gauge risers, pipe (3) interstitial risers, set spillers, and manways.  
•    Set (4) SS islands 48” x 72” 13” 304L grade /#4 polish. Set dispenser sumps and make final connections. 
•    Infill islands.
•    Auger and set (12) 8” bollards. Install sleeve covers G59-3456M. 
•    Set (4) Gilbarco Encore 500’s. NPA, NPB, NAO and NP5.
•    Prep site for concrete
•    Pour 8” tank pad 24’ x 75’.
•    Pour fuel island approach lanes 43’ x 40’.
•    Set new kiosk, set new J.E Adams 9225 Vacuum. 
•    Remove existing tank. Using existing wiring mount the new TLS-450 w/printer. Install all probes and sensors. In parts room install new FSC 3000.
•    Update COPT software to Phoenix. Set new COPT in Kiosk.
•    Fabricate and install new collection boxes on the canopy. Run (4) new downspouts. 
•    Provide Training. Startup system and place in service. 

Bulk Fluids
Description    
•    From fuel island trench 101’ to building. Run 4” flexworks access chase pipe. 
•    Transition from piping to (3) hydraulic hoses. Pull from building through 4” chase pipe to Fuel Island. Make final connections.
•    Run 1” copper water line in same trench next to 4” chase pipe. Stub up and connect to water hydrant at Fuel Island. 
(Location TBD).
•    Erect 6’ by 6” steel pole.
•    Mount (3) Graco reels. (Anti-freeze/washer fluid, Air and Oil).
•    Make final connections.
•    Install Meters.
•    Check existing pumps to make sure they can handle the volume and distance to the fuel island. 
•    Pour concrete over trench 101’